Parallel Flow Aluminum Auto Radiator for Car

Parallel Flow Aluminum Auto Radiator for Car

                      Micro channel parallel circulation radiator professional producer

The condenser-a part of the air conditioning circuit-is integrated into the motor cooling module, where it is utilised to cool down and condense the compressed, gaseous refrigerant from the compressor. We make brazed, flat tube condensers that produce substantial performance in spite of their compact and light-weight layout. They guarantee quick cooling of the passenger compartment thanks to ideal matching of heat transfer and force fall on equally the coolant and the air facet.

The condenser is a warmth exchanger in a cellular A/C technique. Nowadays, condensers are normally produced of aluminum, but in the earlier, some had been made of copper/brass. Condensers look extremely much like radiators, just a little thinner, and considering that they also depend on air flowing via them, are normally located in entrance of the radiator.
Like radiators and evaporators, condensers are also built as a sequence of tubes with fins all around them. its  job is to launch warmth. Far more especially, to release the heat the refrigerant absorbed although it was flowing via the evaporator, quite significantly the exact same way the radiator releases the warmth from engine coolant that the coolant absorbed while it was flowing by means of the engine. The refrigerant enters the condenser as a large-pressure vapor, but as it flows by means of the condenser and cools, it turns back into a cooler higher-strain liquid.

Solution features
1 adopt low height fins and multiple flat pipes to increase the heat dissipation area and improve the heat dissipation performance.
2 fin special treatment to enhance lodging resistance and maintain the tidiness of the products’ appearance 
3 powder coating on the products can enhance corrosion resistance and improve product life cycle.
4 none- argon arc welding solder products look different.
5 every product’s pressure is maintained by using nitrogen so the product is free from leakage at 100% before it leaves the factory

Firm Edge
1. Generic products are supposed to be manufactured strictly according to the installation standard of the original factory, in this way to ensure the accurate installation for the users.
two. This special design for the pin not only enhances its lodging resistance,ensure the visual appearance tidy but also reduces the air blockage chance, it also allows more heat dissipation area to improve heat transfer performance. In that way, the air conditioning system can achieve its expected function more efficiently.
3. Part of the products uses galvanised microchannel flat tube as material or adopt the powder coating treatment, in order to improve products’ corrosion resistance and prolong the service life.
four. By machining core into different thickness and wave distance and changing the amount of holes in flat tube,we can improve the heat dissipation efficiency of condenser of the product, lower down the system compression power, save fuel and improve economic efficiency.
five.CZPTy product is double checked and a pressure-holding device is installed to ensure that every product is 100% leak-free before it leaves the factory.
6. The company with a complete production chain, is focused on the developing new products, and keeping tracking of products to ensure the timeliness of all product supply, and also enhance the flexibility of enterprise operation.
seven.Only when we have an independent team with high efficiency can we satisfy CZPT demands.  

Extended time period enterprise is primarily based on our dependable solutions, quickly react and our professional encounter to Car AC. We are going to turn out to be your associate, not just your supplier.
one.CAD Drawing, and mould layout foundation on your sample
two.Mould examination and sample verification before mass production.
three.CZPTers of a variety of shipping strains.
4.competitive freight delivers and one particular-stop services on clearing, shipping concerns.

Q1. Are you a manufacturing unit or trading business? A: we’re a self -personal manufacturing unit, we provide one-cease provider for our consumers, from spare elements to condenser, from technological product sales to delivery and to soon after-income, so as to preserve the expense for shopper, management the quality and lead time, give the ideal companies
Q2: The place is your factory positioned? How can I check out there? A: Our manufacturing facility is situated in  HangCZPT, Shan dong, China.
The nearest airport is ZheJiang Yaoqiang airport or HangCZPT Liuting airport.
Q3. What is the manufacturing time for new molds and mass manufacturing? A: 7-10 days to build the new moulds, mass generation takes all around twenty-25days for a single 20gp,25-30days for one 40hq, can method urgently if require.
This fall: What is the payment phrases? A: Telegraphic Transfer (T/T) and Letter of Credit history (L/C).
Q5: Can you ship me samples? A: Yes, Samples are for free of charge, and freight is on your side.


Parallel Flow Aluminum Auto Radiator for Car